Emery-Board - concept and meaning

Consider what the concept and meaning of the word means emery-board (информация предоставлена intellect.icu).

n. emery-coated nail-file.

Рифмы

Данное слово имеет следующие слова-рифмы:

Полные рифмы для слова "emery-board":
aboard, afterward, award, awkward, backward, backyard, bard, bargeboard, barnyard, bastard

Рифмы для этого же слова "emery-board", но если ударение на последний слог :
absurd, accord, afford.
Помните, что рифмы могут зависеть от диалектов и произношения, поэтому в некоторых случаях рифмы могут варьироваться.

Вымышленные слова-рифмы для этого же слова (с учетом частотности букв русского или английского языка) "emery-board" :
nitafeard, pekokeard, daloleard, niheciard, lisaweard, tasiwiard, titydiard, bisaseard.


Больше рифм

---

Цифровое произношение

Используя технологию и алгоритмы для преобразования "Emery-board" в числовой формат с целью облегчения их поиска, классификации или сопоставления для достижения цифрового произношения алгоритмами soundex-E561, для metaphone-"" и для double-metaphone AMRP.

See also

... the sandpaper 12 mm from the end of the. rod Strip the end of the rod by rotating it in. an emery paper ring Continue cleaning the rod until it is easy to enter . from the tube ... ... can install on a breadboard with point-to-point soldering You can use a printed circuit board from a set . or make it yourself The circuit board drawing is shown in Fig ... (Robotics)

... of hot melt glue For better contact , you can pre-clean the surface with emery . paper The solenoid is attached to the rear of the aluminum . plate with dimensions of mm on the two ... ... of mm on the two rear .mm racks with several nuts An electrical circuit board and a battery are attached to. the front (see Fig Fig Robot Fish Assembly Waterproofing ... (Robotics)

... with a laser beam The temperature of the connections depends on the absorption of. heat by the components and the surface of the board The disadvantage of contactless soldering technology is the dependence of. the heating of the soldering area on a variety ... ... . side of the board and the components are installed Then the paste is melted and the glue is polymerized . The board is turned over , the paste is applied and. the components are installed on the second side of the.board , after ... (Design and engineering of electronic equipment)

... fragments using a single photomask for a batch .of boards At the first stage of manufacturing in the board blank ., holes are drilled for mounting components and vias to ensure .electrical contact between ... ... stages of production , mounting holes are drilled . in the board , which are used to mechanically fasten the.board to the chassis or to mechanically fasten the elements to. the printed circuit board At the end of production ... (Design and engineering of electronic equipment)

... the manufacturer , you should choose the.material based on the predicted operating temperature of the base of. the board , focusing on the glass transition temperature of the.materials The higher the glass transition temperature ... ... for the. development of the board Replacing the lines with conductive paths , the developer creates a. conductive pattern of the board From the skill of the developer depends on the optimal . location of the components on the board , eliminating the intersection ... (Design and engineering of electronic equipment)

... for the findings And at the same time there is a need for. drilling vias If earlier in the development of the board , the transition . from one side to the other was due to the.hole for the component output , now ... ... to the.hole for the component output , now it is necessary to introduce . a transition hole when designing the board Tracing the board is more difficult , for such work requires . an experienced developer The use ... (Design and engineering of electronic equipment)

---

---